|
|
Post by cedric on Mar 6, 2021 19:35:46 GMT
Hi all,
I've got the wallbox, I've got manual for my V200, but I don't see anything for the connection. Anyone can help me for this? 
I don't know wich cable connect to my 3 prong socket. Ground is the middle cable, but that's all I've find.
Thanks in advance! Cédric
|
|
|
|
Post by Ron Rich on Mar 7, 2021 0:24:17 GMT
Hi Cedric,
Either remove the rear outside door over the amp/TSR, and look at the female plug, or read the schematic for the TSR. Orange is ground-- Green is "hot" and blue is signal. Ron Rich
|
|
|
|
Post by cedric on Mar 7, 2021 5:21:02 GMT
Thanks Ron, I'll do it today.
Good sunday to all.
Cédric
|
|
|
|
Post by cedric on Mar 14, 2021 8:49:03 GMT
Hi everyone,
I've connect my wallbox today, but...
Every time I make a selection, a record is taken, but the wrong one. The mistake is often with the letters. I have already seen this kind of problem in the messages, but I cannot find the topic. Thank you.
Cédric.
|
|
|
|
Post by Ron Rich on Mar 14, 2021 13:16:20 GMT
Hi Cedric,
This type problem is most often in the stepper-- often the problem is the contacts on the transfer switch. Next, the reset dogs are not catching, or one of the step-up coils contacts are out of specifications-- HOPEFULLY, no one has attempted mechanical "adjustments" on the stepper ! They do not change !! if you can-- Listen to it work-- you may hear when it "misses"--- Ron Rich
|
|
|
|
Post by cedric on Mar 14, 2021 14:10:56 GMT
|
|
|
|
Post by Ron Rich on Mar 14, 2021 14:24:59 GMT
Hi Cedric,
Yep-- I can see one of your problems from here ! The step-up wheel with the transfer switch on it has not returned all of the way home-- did you oil the stepper as per the Service Manual ? Ron Rich
|
|
|
|
Post by cedric on Mar 14, 2021 14:57:09 GMT
Thanks Ron 👍 I Don t have yet the manual. Are you talking about this wheel?  Thanks, Cédric. |
|
|
|
Post by cedric on Mar 14, 2021 15:01:07 GMT
|
|
|
|
Post by cedric on Mar 14, 2021 15:55:31 GMT
Ron, sorry, I mixed up a bit. I thought you were talking about the wallbox manual, but I understood that this is the principal's manual. So I oiled as stated in the manual, it's ok. If I spin the wheels (letters and numbers) by hand, they return to the position as in the photo. They seem to turn very easily, freely. I'll give it another try (yes this time I've use translator  ) Thanks, Cédric. |
|
|
|
Post by Ron Rich on Mar 14, 2021 17:02:57 GMT
Yes Exactly the wheel I was talking about being "stuck"-- did you also oil the fiver wheel on those contacts ? If not, you should-- will watch video now and respond in the next few minutes to it-- Ron Rich
|
|
|
|
Post by Ron Rich on Mar 14, 2021 17:07:43 GMT
Cedric,
Do not push on the "ends" of the 'V" that release the dogs-- push only, on the center ! Do a video of that unit with the power on--and while a selection is being made-- Ron Rich
|
|
|
|
Post by cedric on Mar 14, 2021 18:47:30 GMT
Hi Ron, Thanks for all of this informations. My prob is bigger. After some trys, I've heard some craclings and see smoke. Watch the resistance. And where is more strange, is when I touch the read out 2d21, stepper works a lot! it makes a lot of selection alone. There's a sc not far read out 2d21, I'll check it. It's a job to have a jukebox (oups sorry Mr Seeburg, a phonograph ;o) Thanks Ron.  |
|
|
|
Post by cedric on Mar 14, 2021 18:58:17 GMT
Ron,
Where's the 4th and 5th wheels? I oiled the 2 bigs (letters and numbers) also the small on transfer switch, but I don't know where are others.
Thanks, Cédric.
|
|
|
|
Post by Ron Rich on Mar 14, 2021 22:28:50 GMT
Cedric,
As for the
When you find them, let me know as I have never seen them ! I have no idea why the read-out tube would operate the stepper-- the stepper has it's own 2D21 ? As for the burned out resistor-- I don't know what circuit that was in-see the schematic-- Ron Rich
|
|
)